Skip to content

Setting Up A Failover To Cellular (F2C) Network with Opengear

Failover to Cellular (F2C) allows enterprises to efficiently change over to an always available connection when a disruption occurs on the primary, wired internet line. An outage scenario is inevitable. Those with distributed sites, like in the retail industry, are all too familiar with it. When a POS system stops working, organizations are faced with losing business and money, with the cost of downtime at $260,000 per hour.[1] Not being able to process payments, customers will have to go elsewhere or an organization can take a riskier route and manually write down credit card numbers. This opens up a wide range of liability and non-PCI (Payment Card Industry) compliance.

However, if an enterprise has a Failover to Cellular solution in place, or equipment with this capability built in, they are ensured always on network connectivity. If the primary wired internet connection is lost, Failover to Cellular kicks in. Providing speed to keep the network running smoothly, and continued internet connectivity for remote LANs and equipment over 4G LTE, engineers are able to restore the WAN without the need of manual intervention or impacting normal operations. They are then able to automatically activate a secondary connection to reestablish in and outbound network access.

Working similar to the 4G LTE technology on a smart phone, this kind of connection allows enterprises to pay per unit of data. Ensuring a consistent monthly cost depending on the carrier chosen to use, it can be deployed by simply plugging the SIM card from the carrier into the networking equipment.

The Basics of Out-of-Band Management

Article

Network Resilience Across The Globe: How i3D.net Supports Gamers Around The World

Article

Failover To Cellular With Opengear

In Opengear devices, Failover To Cellular is built-in with the internal or external PSTN modems that can be used for this. Once it is enabled, the equipment is able to detect failures by sending ICMP ping requests from the network to a primary and secondary probe address remotely. If these requests fail, the primary connection has been reestablished and the devices automatically fail forward. Opengear devices have three operation modes:

✔ Always Up Out-Of-Band Mode

This is the default mode when no failover scheme has been configured. Failover detection is disabled. Only inbound connections on the cellular interface are routed back out the cellular interface, to enable Out-of-Band access from remote networks, like through incoming SSH. Otherwise outbound network connections, like through a VPN client tunnel or SNMP alerts, are established according to the main static routing table, regardless of network state.

✔ Failover Mode

Failover detection is enabled on the primary interface. The secondary interface remains in a down state with no network configuration. When failover is initiated, the secondary network interface is started and configured. If a default route is installed on the secondary interfaces, it takes precedence over the default route on the failed primary interface. During failover, the outbound network traffic is established from the secondary connection.

✔ Dormant Failover Mode

This mode combines Always Up and Failover mode. Failover detection is enabled, however the secondary interface is kept in a dormant up state. Only inbound connections on the cellular interface are routed back out the cellular interface, to enable Out-of-Band access from remote networks.

When failover is initiated, the default route of the secondary interface takes precedence over the failed primary interface. Outbound network traffic is established out the secondary connection during failover.

Implementing Failover To Cellular

There are many advantages to having Failover To Cellular. Providing remote access even when the WAN and LAN networks are down, engineers have the ability to quickly remediate the issue while having full network visibility. Failover To Cellular is a necessity for enterprises looking to ensure resilience and keep the network running at all times.

A small form factor console server with embedded global 4G-LTE modem for Smart Out-of-Band. 4-8 serial console ports plus 4 USB console ports. Used for branch offices, retails stores and small edge locations.

8-48 software-selectable serial console ports with optional 24 USB console ports or 24 port Gigabit switch. Embedded cellular available for always-on Smart Out-of-Band access. Designed for resilient data centers and large IT deployments.

Secure centralized management of your entire Smart Out-of-Band network. Lighthouse Enterprise offers remote IP access and multi-instance monitoring of your critical locations from a single portal. Standard NetOps tools support advanced automation protocols.

Opengear – Verkkolaitteiden OoB etähallinta

Opengear mahdollistaa turvallisen etäyhteyden ja -hallinnan kriittiselle IT-infrastruktuurille, vaikka verkko olisi alhaalla. Verkkolaitteiden provisiointi, orkestrointi ja etähallinta innovatiivisten ohjelmistojen ja laitteiden avulla mahdollistavat teknisen henkilöstön hallita palvelinkeskuksiaan ja etäverkkopaikkojaan luotettavasti ja tehokkaasti.

Viisitoista vuotta kestäneen historian aikana Opengear on kehittänyt tuotteitaan ja ratkaisujaan yksinkertaisista päätelaitteista nykyaikaisiin monipuolisiin konsolipalvelimiin kehittämällä keskitettyjä hallintaohjelmistoja, sulautettuja 4G-LTE -pohjaisia konsolipalvelimia ja gateway-tuotteita sekä NetOps-valmiita konsolipalvelimia.

Opengear NetOps-konsolipalvelin yhdistää kaistan ulkopuolisen hallinnan ja verkkoautomaation yhdessä yksikössä avoimen arkkitehtuurin työkalujen avulla.

Tutustu tuotteisiin oheisen linkin kautta: Opengear – Verkkolaitteiden OoB etähallinta
Share on facebook
Facebook
Share on twitter
Twitter
Share on linkedin
LinkedIn
Share on email
Email