NEW! Perle IDS-710HP Managed Industrial Ethernet Switches with built-in PoE injector

In addition to transmitting network data, the IDS-710HP has a built-in PoE injector to supply up to 100W PoE per port for a total of 450W across all eight copper ports. Classified as Layer 2 Power Sourcing Equipment (PSE), the switch will detect if connected devices are PoE-compatible and will automatically supply power. The IDS-710HP will not need to be replaced as PDs are updated because, as a fully 803.2bt compliant switch, it supports all PD types, classes, and topologies:

  • Type 1, 2, 3, and 4
  • Class 1, 2, 3, 4, 5, 6, 7, and 8
  • Single-Signature and Dual-Signature

The IDS-710HP also has the ability to reboot attached PDs remotely. A PD power reset from the IDS-710HP will save technicians a trip to the PD location, which may be in very difficult to access locations like exterior walls, ceilings, light posts, pipelines, and kiosks.

PoE Ethernet Switch

Overview

  • 8 x 10/100/1000Mbps PoE 802.3bt Ethernet Ports with 450W of available power
  • 2 x SFP Slots supporting 1G/2.5G Fiber or 10/100/1000Base-T
  • PROFINET and Modbus TCP protocols supported for monitoring and device management
  • Ring Protocol MRP (IEC 62439-2) has <10ms recovery time
  • STP/RSTP/MSTP for network redundancy
  • Advanced Security and IT management features: TACACS+, RADIUS, 802.1x, SSH, SNMPv3, and HTTPS
  • IEEE 1588 V1 and V2 PTP for microsecond accuracy
  • Advanced protocols to optimize the performance and intelligence of the network: IGMP Snooping, LLDP-MED, GVRP, Voice VLANs, MSTP, GMRP, and IPv6 MLD Snooping

The IDS-710HP is a 10 port Managed Ethernet Switch that can operate in industrial environments providing advanced performance and enabling real-time deterministic network operation. Eight 10/100/1000-Base-T Ethernet ports are available for networking Gigabit and Fast Ethernet devices. The two SFP slots support 10/100/1000 on Copper or 1G/2.5G on Fiber.

In addition to transmitting network data, a the IDS-710HP has a built-in Power over Ethernet injector to supply up to 100W Power over Ethernet (PoE Type 3 & Type 4) per port for a total of 450W across all 8 ports. This is ideal for powering standards-based 802.3af, 802.3at, and 802.3bt compliant devices such as such as pan-tilt-zoom (PTZ) security cameras with heaters, 802.11ax/ac wireless access points, alarms, traffic controllers, sensors, and tracking devices. Classified as Layer 2 Power Sourcing Equipment (PSE), the switch will detect if connected devices are POE-compatible and automatically supply power. Using a PoE Switch saves on installation and maintenance costs by eliminating the need to install multiple pieces of equipment, additional electrical wires, and outlets. This flexibility allows for easy adaptation to network growth and changes.

The SFP slots allow for flexible network configurations using SFP transceivers supplied by Perle, Cisco or other manufacturers of MSA compliant SFPs. In addition, they make utilizing fiber is easy in environments where high levels of electromagnetic interference (EMI) is a common phenomenon, like industrial plants. This interference can cause data corruption over copper-based Ethernet links. However, data transmitted over fiber optic cable is completely immune to this type of noise ensuring optimal data transmission across the plant floor.

Perle Industrial-grade Ethernet Switches are designed to stand up to extreme temperatures, surges, vibrations, and shocks found in industrial automation, government, military, oil and gas, mining and outdoor applications. These rugged fan-less switches are hardened to provide superior reliability in -10 to 60°C. Or, choose the IDS-710HP-XT, where every component has been designed and tested to handle operating temperatures between -40 and 70°C.

The simple Plug and Play installation available in Perle’s Fast Setup feature gets your Ethernet devices networked immediately. The familiar Command Line Interface (CLI), via in-band Telnet or the out-band serial console port, will be appreciated by CCNA (Cisco Certified Network Associate) and CCNP (Cisco Certified Network Professional) trained engineers.

The IDS-710 Managed Switches have Enterprise-grade features for environments where extensive security, QoS, and network integration functionality is required. They can be managed with an IPv6 address and supports a comprehensive set of management functions including MRP (IEC62439-2), PROFINET, Modbus TCP, management VLAN, Management Access Lists, Password Strength requirements, RMON, N:1 port mirroring, and local alert log.

All Perle Industrial Ethernet Switches only use high-end components from the leading chip manufacturers to ensure the highest level of durability and reliability. In addition, all units have a corrosion resistance aluminum case and dual redundant power input with reverse polarity and overload protection.

Perle has been designing industrial hardware since 1976. We used this expertise to design the toughest Ethernet switches on the market that will keep your system running for years to come.

Application Diagrams